Rebar, Mesh & Construction Supplies (Pty) Ltd trading as RMCS
Rebar, Mesh & Construction Supplies (Pty) Ltd t/a RMCS
571 Setter Road, Commercia Industrial
MIDRAND, Gauteng Province, 1685
South Africa
Phone#: +27 (0)11 310 8660 / 2324 / 7113     Fax#: +27 (0)86 545 6012
email: [email protected]
email: [email protected]
iv>
Our Products ABC.....

 EMPOWERDEX BEE Rating
"AAA" - Level Two Contributor
Click here to view or print our 2016/7 BEE certificate
Click here to view or print our 2015 BEE certificate
OUR PRODUCTS
HOME
OUR PARTNERS
ASSOCIATIONS
NEWS
CONTACT US
Try our scaffolding accessories!
Base jacks, formwork, scaffolding accessories Combi nuts, Tie nut, formwork, scaffolding accessories Swivel Couplers, Fixed Couplers, formwork, scaffolding accessories Click here to go to the Automatic Rebar Fixing Machines page Click here to go to the Radolid web page Click here to go to the Bosch Scanner web page Click here to go to the Electrical Control Systems web page Click here to go to the Casing end Seals web page
Automatic Rebar Fixing Tools
Reduces rebar fixing time, up to 5 times faster than manual fixing. Makes a rebar tie in approximately one second with consistant strength. Easy to operate - Learn to use Rebar Tier in minutes. Reduce risk of health problems, Ergonomics and reduction in the probability of an injury such as carpal tunnel injuries. Extension arm Reduces constant bending. One hand operation allows worker to hold rebar while fixing it. Battery operated, no electrical cords to trip over or to get tangled. Battery charges within 25 to 30 minutes. Reinforced Steel Fixing tools that are currently available are the RB215, RB395, RB515, RB655 and RB700. With this range of rebar fixing tools a wide range of sizes of reinforced steel can be fixed quickly and efficiently.

Visit our Rebar Fixing Overview page for more information.

Visit our Automatic Rebar Fixing Tools - Site Photos page to see the wide range of applications where our automatic rebar fixing tools are being used.

BOlt & NUT PROTECTION CAPS - RADOLID®
RADOLID® bolt and nut protection caps will protect bolts and nuts for years from external elements which create deterioration and corrosion. Protective grease can be applied to the botl or nut before covering it with a RADOLID® protective cap. Clipping the RADOLID® protective cap on is easy and removing it is just as easy when inspection is required. Using a RADOLID® protection cap will result in huge savings in bolt and nut maintenance cost. For more information on these cost saving devices visit our Radolid® Protection Caps web page.

Bosch Scanners for Metal & Rebar Detection
The Bosch Wallscanners locates all ferrous and non-ferrous metals, electric cables, wood and even plastic with the greatest precision. Its unique technology makes it extremely reliable, providing a degree of safety when drilling, that has never been seen before. Reinforced steel, copper pipes and plastic water pipes, for example, are displayed accurately with the respective permissible drilling depth up to a maximum depth of 100 mm The highest precision and absolute reliability, identical results even with repeated measurements. Information on the permitted drilling depth for all localised objects. Clearly laid out and easy-to-understand display Easy operation with logical guidance in the display Sturdy and durable design for use on building sites.

Visit our Bosch D-TECT 100 web page or Bosch DMF 10 Zoom web page for more information about the specific models.

BRECON ELECTRICAL CONTROL SYSTEMS
Electrical control systems offer you the possibility to directly select which formwork you want to vibrate and when.They represent an open system, which comprises the most modern control technology, however older and already installed vibration equipment can also be integrated into it. The flexibility of these system are unequalled. For more information visit our Electrical Control Systems web page.

BRECON FREQUENCY CONVERTERS
Frequency converters are required for operation of vibrators with 6000 oscillations per minute. In addition to converters with a fixed frequency of 200 Hz, BRECON also supplies converters with variable output frequency. These variable converters allow the frequency and thus the centrifugal force (acceleration) to be adapted to the requirements of the concreting operation and the respective formwork conditions. For more information visit our Electrical Control Systems web page.

CASING END SEALS
RMCSPL End Seals outperform the costly and labour intensive brick and mortar method of sealing casing ends. While soil stress and pipe movement cause mortar to crack, the RMCSPL products move with the pipe, insuring the integrity of the seal. Unlike link-type sealing blocks that are limited to carrier/casing differential and can only be used on a concentric profile, the RMCSPL seals are totally flexible. RMCSPL offers four types of end seals which can accommodate any combination of pipe sizes. Visit our Casing End Seals web page for more information.

In addition, Innerlynx® forms a mechanical seal between pipelines and casing. Innerlynx forms a hydrostatic seal and electrically insulate the carrier pipe from the casing. Innerlynx can be installed by one person and requires no special tools. Visit our Innerlynx® Penetration Seals web page for more information on this first class product.

CASING SPACERS & CENTRALISERS
APS Casing Spacers centre water and sewer pipes in casings with ease of installation, are virtually corrosion proof and provide insulating protection from a possible electrical shorting between the carrier pipe and casing. No special tools are needed, no grease is used and they are easily bolted on by a single worker. APS Casing Spacers eliminate the need to fill the casing annulus with sand which is extremely labor intensive. Sand in the annulus also acts as an electrolyte thereby introducing unwanted current to the steel or ductile iron. With no need for this fill, APS Casing Spacers are your answer to lower installation costs with continued access for maintenance.

Casing insulators are used to support and electrically insulate a pipeline from a casing pipe through which it must pass and are used in river crossings, canal crossings and bridge crossings as well as highway and railroad crossings. We recommend installation of polyethylene casing insulators every 1,8 to 2,4 meters. Visit our Casing Spacers web page for more information.

REBAR CENTRALISER
RMCS Rebar Centralisers are used to centralize steel reinforcing in the centre of a pile.

These centrailsers provide a cover of 30mm and will accept reber up to a size of 25mm. Visit our Centraliser web page for more information.

CONCRETE REBAR CHAIR SPACERS OR CONCRETE COVER BLOCKS
The RMCSPL has a range of concrete rebar chair spacers or cover blocks with Certified strength to withstand extreme rebar weights or pressure. These concrete rebar chair spacers come with embedded fixing wire for easy fixing to rebar. They have a wide base to ensure best support without tipping or falling over and are quick and easy to install. Visit our Concrete chair spacers web page for information about concrete cover sizes and packaging.

These concrete rebar chair spacers or cement cover blocks are made by casting them into rubber moulds.

CONCRETE WHEEL SPACERS OR CIRCULAR SPACERS
Concrete wheel spacers (Circular spacers) or column cover blocks are used to ensure consistant concrete cover for columns and walls inside the concrete shutter. Wheel spacers help to ensure the centralisation of rebar inside the shutter. The notched outer rim of the wheel spacers ensure minimum contact with the shutter. Visit our Concrete Wheel spacers web page for information about concrete cover sizes and packaging.

These wheel spacers are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

CORE DRILLING MACHINES
The RMCSPL range of Eibenstock core drilling machines are made to tackle any core drilling job. The range of Eibenstock core drilling machines consist of the the DBE 162, DBE 250, DBE 300, DBE 350 E and ETN 152-3 P. To have a closer look at the specifications each core drilling machine, have a look at our Eibenstock Core Drilling Machines web page.

CORNER FILLETS OR CHAMFERS
Corner fillets or chamfers are used to chamfer corners of cast concrete such as beams, columns, slabs or pre-cast concrete products. Made from durable PVC and can be re-used a number of times. View our Corner Fillets or Chamfers with extension or Corner Fillets or Chamfers without extension web pages for more information about sizes and lenghts.

These corner fillets or chamfers are made from plastic (polyurethane or polypropylene) using a plastic extrusion process.

CONCRETE COVER BLOCKS OR REBAR CHAIR SPACERS
The RMCSPL has a range of concrete cover blocks or rebar chair spacers with Certified strength to withstand extreme rebar weights or pressure. These concrete rebar chair spacers come with embedded fixing wire for easy fixing to rebar. They have a wide base to ensure best support without tipping or falling over and are quick and easy to install. Visit our Concrete chair spacers web page for information about concrete cover block sizes and packaging.

Concrete cover blocks or cement spacers.

DAMP COURSE
Practically all building materials absorb water. This should not and need not be a problem. In reality water is the single most damaging cause of structural decay. Rising Damp is responsible for more building maintenance costs than any other cause.

Dry Rot, Wet Rot, Rising, Lateral and Penetrating Dampness along with condensation, all arise because of unwanted and unnecessary water in buildings. These conditions create the perfect environment for the growth of fungi and the spread of wood destroying insects.

If treatment is delayed for any reason the damage will be much more than cosmetic. The fabric of the building will be damaged and its structural integrity threatened to a point where it will become unsafe. When the external signs become evident - damage has already begun. There should be no delay in undertaking remedial work. Delay will incur additional risk and cost.

Rising Damp is a very real possibility wherever a wall is in contact with the ground. The soil, which normally has a high moisture content, acts as a reservoir. The evaporation of water from the surfaces of the wall exposed to the air cause the fabric of the wall to act as a 'sponge' drawing moisture up from the ground, through the bricks, stone or mortar. Depending on the construction and materials of the wall serious damage can occur anywhere up to 1.2 metres above ground level.

Lack of, or the presence of an ineffective damp course will inevitably lead to Rising Damp and all the attendant damage that entails. To view pictures of our product and pictures of how to install damp course, view our Damp Course web page.

DUOCON CENTRALISERS
DuoCon Centralizers are used to support and space a section of pipe inside a secondary pipe on dual containment systems. These plastic centralizers can be used on all types of pipe including fiberglass, PVC, polyethylene and steel. APS centralizers are manufactured from injection molded, high density polyethylene. Centralizers are also called spacers or spiders. Visit our DuoCon Centralizers web page for more information about this unique product.

EIBENSTOCK ETS 225 DRYWALL SNADER
The Eibenstock ETS 225 Drywall Sander is a lightweight tool with convenient handles for large surfaces. The ETS 225 is the ideal tool for dry-wall construction. Wall and ceiling connections of plasterboards can be sanded quickly and cleanly before decorating or plastering. The big sanding disc works effectively. Due to its ergonomic design and distribution of weight, the tool can be guided easily on walls or ceiling for extended periods of time. The tool can be applied to further applications such as timber flooring, boats, vehicles, containers etc. by means of different accessories. For more information about this dynamic peice of equipment, view our Drywall Sanders we page.

EXTERNAL VIBRATORS FOR THE CONCRETE COMPACTION INDUSTRY
There are 2 methods of compacting concrete via external vibration. Wet-cast concrete gets consolidated by external vibrators mounted to the outside of a mould. This reduces the cohesion and friction between the components. Grains are therefore able to become denser and the enclosed air can move upward and escapes. Dry-cast concrete achieves compaction through external vibrators on top. With this method the concrete gets pressed and the enclosed air of the concrete moves out. Visit our Concrete Compaction web page for more information about our External vibration technology.

EXTERNAL VIBRATORS FOR THE CONVEYING INDUSTRY
For applications like conveying, sieving, loosening and breaking-up, BRECON offer a big range of external vibrators from 500 1/min up to 3.000 1/min. All these vibrators are available in 50Hz and 60Hz mains frequency and on request special executions (e.g. 500V) are available. We would be pleased to help you selecting the correct vibrator for your application. Visit our External Vibrators for the Conveying Industry web page for more information.

FERRULE TUBE PUSH-ON CONES
Ferrule tube push-on cones are used as ends on ferrule tubes to space shutters. Fits on the inside of the tie-rod sleeve. Can be removed after the shutters have been dismantled and be used again. Visit our Ferrule Tube Push-on Cones (End cone) web page for information about sizes and packaging.

These ferrule tube push on cones are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

FIBRE CONCRETE, FIBRE CEMENT SPACERS OR COVER BLOCKS
RMCS has a range of fibre concrete rebar chair spacers, also referred to as fibre cement cover blocks, with Certified strength to withstand extreme rebar weights or pressure. These fibre concrete rebar chair spacers come with embedded fixing wire for easy fixing to rebar. They have a wide base to ensure best support without tipping or falling over and are quick and easy to install. Visit our Concrete chair spacers web page for information about concrete cover sizes and packaging.

These fibre concrete rebar chair spacers or fibre cement cover blocks are made using a concrete extrusion process.

FLANGE BAND PROTECTORS
NEW Kleerband Flange Protectors are the quick, easy and effective way to apply protection and prevent corrosion. Why try and protect flanges the old way when APS has the new, clear advantage to prevent corrosion? Kleerband Flange Protectors are manufactured of 100% virgin vinyl compound, which allows visual inspection of the flange surface without removing the flange protector. For more information on how to protect your flanges visit our Flange Band Protectors web page.

FLANGE INSULATING GASKET KITS
Flanges, the most common trouble area, need to be sealed properly to prevent leakage and must also be cathodically insulated to prevent stray currents which cause undo corrosion and eventual breakdown of the metal. Advance Products & Systems manufactures and maintains a supply of quality products and materials which help solve most flange sealing problems, therefore preventing subsequent corrosion and saving the integrity of the pipeline. For specifications and related products view the RMCSPL Flange Insulating Gasket Kits web page.

FLANGE PROTECTOR GREASE
Advance Flange Protectors and corrosion inhibitor grease are recommended on all insulated flanges. By encapsulating the flange cavity with the flange protector and injecting our corrosion inhibitor grease, you can rely on your cathodic protection system to provide you with years of trouble free service. For more information on how to protect your flanges visit our Flange Band Protectors web page.

FLUSH CUTTING SAW
The DFC20A Flush Cutting Saw is a new addition to the DIAMOND line of electric tools for the construction industry, it's a multipurpose cutting tool that can be used on a lot of different materials found on the job: rebar, all-thread rod, locks, chain, EMT conduit, copper pipe, steel rods, etc. It is excellent for cutting material flush with concrete. It makes no sparks and leaves no burrs. For more information on our Flush Cutting Saw visit our Flush Cutting Saw web page.

HAMMER CUSHION PADS - PROTECT YOUR EQUIPMENT WITHOUT SACRIFICING POWER OR YOUR PROFITS
APS Hammer Cushion Pads have proven themselves in all types of pile driving applications. APS has the ability to cut pads to your specifications. Hammer Cushion Pads have to be strong to withstand the pounding and to transmit the driving force needed while protecting your equipment and the pile. APS pads are the best in accomplishing this task. For more information on this unique product visit our Hammer Cushion Pads web page.

INNERLYNX® Penetration Seals
INNERLYNX® forms a mechanical seal between pipes going through walls, floors, vaults, tanks and pipeline casings. Besides being designed to form a hydrostatic seal of up to 40 PSIG and up to 28,8 meters of head pressure, INNERLYNX® helps absorb vibrations, shocks, and sound waves. Being non-conductive, INNERLYNX® electrically insulates the inner carrier pipe from the penetrated structure. With this being a desired property in many applications in preventing a shorting effect from stray currents, it is particularly useful in sealing the gap between electrical conduit and the outer conduit or between electrical conduit and the opening. INNERLYNX® can be installed easily and quickly by one worker with no special tools required. Visit our Innerlynx® Penetration Seals web page for more information on this first class product.

INSULATING SLEEVES AND WASHERS
Insulating sleeves manufactured of high density polyethylene, NEMA grade LE phenolic, and Mylar are available in a full range of sizes. Also available are one-piece integral sleeves and washers which are made of Minton, providing superior compression strength. Integral sleeves are available in sizes through 37.5mm. A variety of high temperature sleeves are also stock items. With each insulating washer, a 3.1mm thick S.A.E. electro-plated steel washer is provided to protect the insulating washer from damage by the nut. Advance flange insulation sets are available in single washer or double washer kits. For specifications and related products view the RMCSPL Flange Insulating Gasket Kits web page.

INTERNAL AND EXTERNAL VIBRATORS FOR THE CONCRETE INDUSTRY
The RMCSPL range of BRECON internal and external vibrators are suitable for a wide range of concrete compaction - dry-cast and wet-cast concrete. Visit our Vibration Technical Applications for more information about what Concrete vibration technology is available form RMCSPL.

INTERNAL VIBRATORS FOR THE CONCRETE INDUSTRY
Internal vibrators are well suited for rough applications and a long service life. Thanks to the optimal power output of the motor the rotation speed always stays constant, even under extrem load requirements. These internal vibrators are designed to make servicing them easy. Visit our Internal Vibrators web page for more information about our Internal Concrete vibration technology.

ISOJOINT® (MONOLITHIC / ISOLATING JOINT)
IsoJoint® is a true monolithic isolating joint. The most up-to-date, patented joint on the market, IsoJoint® does not depend on the use of insulating sleeves and washers for bolts nor insulating gaskets or O-rings between flanges. Why? These insulating gasket kits require a critical, even surface to provide regular and variable crushing and must be maintained over the life of the insulator. External pressure, causing an uneven load on the flange area, can result in loss of insulating properties as well as the transported fluid. Visit our Monolithic isolating joint (ISOJOINT®) web page for more information on this unique and long lasting product.

ISOJOINT® METER SERVICE FITTINGS
ISOJOINT® Meter Service Fittings are manufactured in accordance with the highest technical standards which guarantee that mechanical requirements are met for the specific needs of a plant and that insulating requirements are met and surpassed with regard to the electrical characteristics of the product carried in the pipeline. For more information about this product visit our Meter Service Fitting web page.

JOINT BARS ALSO CALLED GROUTING PROFILES
Joint bars or Grouting profiles as they are calles are used to create features on concrete walls or hide joins. Can be nailed or screwed or nailed to a shutter. Made from durable PVC and can be re-used a number of times. View our Joint bars web page to see the different sizes that we manufacture.

These joint bars or grouting profiles are made from plastic (polyurethane or polypropylene) using a plastic extrusion process.

KNIPEX BOLT CUTTERS & CONCRETE MESH CUTTERS
The Knipex range of bolt cutters and concrete mesh cutters have blades made from high performance Chrome Vanadium steel, oil-hardened and tempered. Precision cutting edges are additionally induction hardened. To view the sizes that are available and more technical information, visit our Knipex Bolt Cutters web page.

KNIPEX CONCRETORS PLIERS
The Knipex Concretors Pliers are the best pliers for rebar fixing on the market today. They are robust and durable and are the most preferred concretors pliers in the reinforced steel fixing trade today. The main application for the Knipex Concretors Pliers is twisting and cutting off tie wire when fixing the rebar. Visit our Knipex Concretors Pliers for more information about this top of the range product.

Knipex concretors pliers together with our Automatic Rebar Fixing Machines is a must for every contractor who wants to save many hours on fixing reinforced steel and ultimately on the project.

MANUAL REBAR CUTTER AND BENDER
This well designed combination machines is a must for every site. It will save a contractor time and money and pay for itself many time over. Our manual rebar cutter/bender is designed for cutting and bending reinforced steel (Rebar). Its blades are made from drop-forged high grade alloy tool steel and heat-treated to last. Cuts rebar safely, cleanly and efficiently with minimal effort. Bends rebar up to 180 degrees with versatile operation. Cutting and bending head can be bought and replaced separately. For more information about this unique and cost effective tool for cutting and bending rebar visit the RMCSPL Manual Rebar Cutters/Benders web page.

OIL PIPELINE NIGHT CAPS - KEEP UNWANTED ITEMS OUT
Available in 75mm to 1.05 meters sizes, Foreman Night Caps guard against water, mud, rocks, skids, bottles, cans, animals and other accumulation found in both new and old pipelines. For more information on this quality product visit our Foreman Night Caps web page.

PERMANENT CONES
Ferrule tube permanent cones could be used as a substitute for ferrule tube end cones (push-on cones). They remain in the concrete after the shutter has been removed and are plugged with a matching cap to ensure a clean and neat finish of the concrete casting. They save time and money because labourers won't have to patch up unsightly holes left as a result of tie rod holes. Visit our Ferrule Tube Permanent Cones web page for information about sizes and packaging.

These ferrule tube permanent cones are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

PIPELINE SUPPORT SYSTEM - INSPECT-A-LIFT®
The Inspect-a-Lift® system provides the proven solution to crevice corrosion at pipe supports. This type of corrosion is one of the major causes of external corrosion failures on piping systems. Standard pipe supports can cause premature paint failure and are often tough to access for maintenance. Visit the RMCSPL Pipe Support Systems web page to learn more about this innovative pipe protection system.

PORTABLE COMBINATION REBAR CUTTERS AND BENDERS
DIAMOND portable combination rebar cutters and benders come with a more 25 year proven track record and reliability for on site reinforced steel cutting and bending. They are the best quality portable, single phase combination rebar cutting and bending machines on the market today. Contractors like their portability, reliability and the ability run on 220 volt single phase power. Contractors using these portable rebar cutting and bending machines soon find out that these tools are invaluable. DIAMOND portable rebar cutters and benders are faster and safer to use than jigs or any other manual bending methods. Manual bending methods take at least ten to twenty times longer than our machines and are not as consistant. The models available are the DBC-16H and DBC-25X. Visit our Portable Combination Cutters/Benders web page for information on these high quality cost saving machines.

PORTABLE REBAR BENDERS
The RMCSPL range of electric portable rebar benders have a proven track record of over 25 years. They are the most reliable and of the very best quality portable electric rebar benders on the market today. Contractors like their portability, reliability and the ability run on 220 volt single phase power. Contractors using these portable rebar bending machines soon find out how invaluable these tools are. Made by IKK-DIAMOND in Japan, these portable rebar benders are faster and safer to use than jigs or any other manual bending methods. Our DBD-16L will bend 16mm rebar 180 degrees in just 1.5 seconds. Manual bending methods take at least ten to twenty times longer and are not as consistant. Our robust and reliable heavy duty, DBD-25H bender can be used on site or as production machine. We also stock the DBR-32WH and DBD-32X rebar benders. Visit our Portable Rebar Benders web page for more information about these high quality cost saving machines.

PORTABLE REBAR CUTTERS
The RMCSPL range of electo hydraulic portable rebar cutters have a proven track record of over 25 years. They are the most duarable, reliable and of the highest quality of all the portable electo hydraulic rebar cutters on the market today. Contractors like their portability, reliability and the ability run on 220 volt single phase power. Contractors using these portable rebar bending rebar cutting machines soon find out how invaluable they are. Made by IKK-DIAMOND in Japan, the rebar cutters are faster, safer and more economical to use than abrasive blade cutters or an oxygen/acetylene cutting torch. Abrasive blades or cutting torches take at least twice the time that it takes a DIAMOND rebar cutter to cut any size of reinforced steel.A set of cutting blocks can cut through 4,000 to 8,000 pieces of rebar before thay need to be replaced. We stock and supply the DC-16LZ, DC-16W, DC-20WH, DC-20W, DC-20HL, DC-25W and DC-32WH 220 volt rebar cutters and the DC-1618 battery operated rebar cutter. Visit our Portable Rebar Cutters web page for more information about these high quality cost saving machines.

PORTABLE STEEL PUNCHES
Our unique portable steel punches will quickly and conveniently punch through Flat Bar and save you a lot of time and money!!!! Made by IKK-DIAMOND in Japan these handy puncher's fast punching action produce burr-free holes in a less than a tenth of the time that it will take you to drill any hole. The DIAMOND handy puncher can produce round and elliptical holes in a fraction of the time required by conventional methods. The models which are available are the EP-1406V, EP-1475V, EP-19V, EP-20S and EP-2110V. For more on this unique and handy product visit the RMCSPL Overview of Punches web page.

QUAD SEAL TROJAN
Four seals on the new Quad-Seal Trojan further insures the integrity of the sealing capability of an already-proven reliable gasket. For areas where absolute zero leakage is a must, the Quad-Seal Trojan works twice as hard. For specifications and related products view the RMCSPL Flange Insulating Gasket Kits web page.

REBAR CHAIR SPACERS OR COVER BLOCKS
Rebar Chair spacers or cover blocks are used to support rebar on a deck, which includes radial grounding, heavy duty rebar laying and beams. The wide base of these rebar chair spacers or cover blocks prevent the chairs from tipping over. The design ensures freeflow of concrete and minimal contact with the concrete formwork. Visit our Chair spacers web page for concrete cover sizes and packaging.

These rebar chair spacers or cover blocks are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

REBAR CLIPS
Rebar clips are similar to rebar chair spacers and are used to support rebar or mesh on a deck, which includes radial grounding, heavy duty rebar laying and beams. The wide base of these rebar clips prevent the clips from tipping over. The design ensures freeflow of concrete and minimal contact with the concrete formwork. Visit our Rebar clips web page for concrete cover sizes and packaging.

These rebar clips are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

REBAR SAFETY CAPS OR REBAR END CAPS
Our Rebar Safety Caps can be used to protect construction workers from the danger of being pierced by pertrudung rebar. Rebar sticking out from pillars or colums on a slab present the real danger of piercing workers who may trip and fall on site. Rebar sticking out from the sides of slabs could cause workers to loose an eye. The minimal cost of using rebar safety caps on a construction site is insignificant compared to lost man hours that may result from injuries. Using our rebar safety caps is a small price to pay for the safety of workers on site. Visit our Rebar Safety Caps web page for sizes and packaging.

These rebar safety caps or end caps are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

RECKLI FORMLINERS AND ACCESSORIES
Reckli formliner are the easiest and most convenient way in which to give character to precast or in-situ concrete. A more environmental freindly landscape can be created by turning old fashioned and bland concrete blocks into eye pleasing structures. Standard formliners can be purchaed or your own unique patterns can be created by using our Reckli DIY products. A photo can also be converted to a formliner and precast for permanance.

To see our catalog with and extended range of formaliners Visit our Formliners web page, to see how to create your own unique formliners visit our DIY Formliners web page, To see how a photograph can be turned into a concrete landmark, visit our Photo Engraving Formliners web page and to find out what accessories we have availaable, visit our Reckli Accessories web page.

RUBBER COATED U-BOLTS
Corrosion occurs due to metal contact between the uncoated u-bolts and pipe. The excessive corrosion and pitting can eventually develop into pinhole leaks. This interaction can be completely eliminated by utilizing an APS Pipe Support Pad and APS U-Bolt-Cote. (As shown to the left.) U-Bolt-Cote is excellent for use on plastic, FRP or glass-lined pipe for shock absorption. Visit our Rubber coated u-bolts web page for more information.

RUBBLE CHUTES
Rubbish chutes or Rubble Chutes are the perfect way to remove rubble or household waste safely from multi-storied buildings to the rubble dump or waste container. Visit our Rubble Chutes / Rubbish Chutes web page for more information about this "Safe Site" product.

SAFETY SPRAY SHIELDS
Safety Spray Shields are used to prevent injury to personnel or damage to equipment in the event of a leak or spray-out of acids, caustics, chlorine and other dangerous liquids at piping connections (such as flanges, valves, or expansion joints) found in chemical, pulp/paper, petrochemical and wastewater treatment plants. These Safety Shields are commonly referred to as flange guards, flange covers, flange diapers or flange protectors. Our Safety Spray Shields are constructed from PTFE, polypropylene, PVC, polyethylene and stainless steel and are used for preventing spray-out of hazardous chemicals due to gasket or packing failure on flanges, valves and expansion joints. For more information visit our Safety Spray Shields web page.

Swivel Clamps
Swivel clamps / Swivel Couplers ae used to connect scaffold tubes at any angle. Our swivel clamps / swivel couplers are made of forged steel and are galvanised. For more information visit our Swivel Clamps web page.

TIE-ROD PROTECTION PIPE HEADS OR FERRULE CONES
Tie-rod protection pipe heads or ferrule end cones are used as ends on tie-rod sleeves (ferrule tubes) to space shutters. Fits on the inside of the tie-rod sleeve. Can be removed after the shutters have been dismantled and be used again. Visit our Tie-rod Pipe Head web page for information about sizes and packaging.

These Tie-rod protection pipe heads or ferrule cones are made from plastic (polyurethane or polypropylene) using a plastic injection moulding process.

TIE-ROD SLEEVES OR FERRULE TUBES
Tie-rod sleeves or Ferrule Tubes are used to space shutters and to recover expensive concrete shutter tie-rods (through ties). The inside diameter of the tie-rod sleeve (ferrule tube) needs to be at leat 1mm greater than that of the tie-rod (through tie) being used to fix the shutter. Visit our Tie Rod Sleeves web page for information about sizes and lenghts. These joint bars or grouting profiles are made from plastic (polyurethane or polypropylene) using a plastic extrusion process.

These Tie-rod sleeves or Ferrule Tubes are made from plastic (polyurethane or polypropylene) using a plastic extrusion process.

TRIANGULAR CHAMFER WITH SLOTTED LIP - PLASTI-CORNER
Chamfers or Corner fillets are used to chamfer the corners of cast concrete such as beams, columns, slabs or pre-cast concrete products. Our most modern technological mabufacturing process ensures a perfect fit to your shutter. The highest quality materials are used to give you a number one product that can be used a number of times. No more battles to try to fit your slotted chamfer to you shutter!! Visit our Chamfers with slotted lip web page to see what sizes we have available for you.

These Chamfers, also called Corner fillets or plasti corners are made from plastic (polyurethane or polypropylene) using a plastic extrusion process.

TROJAN SEALING GASKETS
Trojan gaskets are state-of-the-art in near zero leakage static sealing. The elastomer sealing element is encapsulated in the electrically insulated retainer. The encapsulation of the sealing element permits only micro-exposure of the seal to hostile environs of fire, chemicals and corrosive fluids. For specifications and related products view the RMCSPL Flange Insulating Gasket Kits web page.

WALL SLEEVES
Protect your investment and use APS wall sleeves to provide a better seal than a core drilled hole. In the absence of wall sleeves, mechanical/utility piping vibration can cause costly wall damage. In addition, wall sleeves make it easy to repair piping without damaging the wall. For more information about this products visit our Wall Sleeves web page.

Water Stopper
Water Stopper / Water Stops are used in concrete masonry construction of hydraulic structure to safeguard from hydrostatic pressure and water seepage. Our Water Stopper / Water Stops are made from malleable Casting and has a safe working load of 90 KN. Threading is suitable for 15/17mm tie rod and comes with 2 plastic adoptors. For more information about our water stoppers visit our Water Stopper web page.